PACKAGING, CONSIDERED.
MAGNETIC RIGID BOX

Body care gift box.
Three shapes, one set.

Closed blue-grey body care magnetic gift box with a navy YDP logo and full-width front flap
01 / CLOSED BOX · Matte paper and navy branding.

A magnetic gift box for a bottle, jar and tube, with a paperboard insert shaped for each product.

Minimum order: 500 pieces. Start with a photo or an idea.

Discuss my gift set See how the products fit

The packaging at a glance

Construction
Fixed magnetic rigid box; supplied assembled
Finish
Matte blue-grey wrap; navy printed logo
Insert
Ivory paperboard; three shaped positions

PACKAGINGFinal fit and finish require a physical sample.

Explore this case 6 sections

Fit a bottle,
jar and tube.

Open magnetic body care gift box with a pump bottle on the left, a round cream jar in the centre and a hand cream tube on the right
02 / LOADED SET · Separate positions and removal access.
  1. 01

    Bottle: protect the pump.

    Support the body, leaving the packed pump clear of the lid and insert edges.

  2. 02

    Jar: support the base.

    Set its height so fingers can grip the jar and the lid can close above it.

  3. 03

    Tube: leave room to lift.

    Allow for the cap, taper and sealed end without squeezing the tube.

Review my product combination ↗︎

A paperboard insert
with support below.

Empty ivory paperboard insert with separate pump-bottle, round-jar and tapered-tube positions, with all three products beside the blue-grey box
03 / EMPTY INSERT · Shaped openings and finger notches.

The openings locate each product. Folded supports underneath carry its weight; finger notches provide access. Support heights can differ across the set.

How does the support work?Illustrative cross-section
An illustrative paperboard insert support section A container passes through an opening in the insert face and rests on a folded support above the box base. Three numbered labels identify the opening, folded support and base. This is a proposed principle, not the construction of a tested sample. 123
Illustrative only; not a production dieline or a tested sample.
  1. Opening locates the container.
  2. Folded support sets the resting height.
  3. Box base carries the load below.

Develop board stiffness, reinforcement and retention around the actual filled containers. A shape-matched opening alone does not establish secure retention.

A magnetic lid
that stays attached.

5-SECOND PREVIEW · Loaded set, then empty insert.
Watch the layout & read the video notes ↗︎

The rear hinge keeps the lid connected; the front flap closes magnetically. Allow space behind the box to open it.

Supplied assembled. Include the fixed box volume when planning shipping.

Explore magnetic box options ↗︎
Would a lift-off box suit the same set?Compare opening, packing and delivery scope
THIS DESIGN

Fixed magnetic box

Keep the lid connected and present the set from above. Review the rear hinge, front flap alignment and space needed to open it.

AN ALTERNATIVE

Lift-off rigid box

Remove the lid completely for access from any side. Allow somewhere to place it and review the lid-to-base fit.

Compare both with the same products, finish, insert and quantity. A collapsible version would require a separate structural and assembly review.

Help me choose the box structure ↗︎

Materials, finish
and custom options.

Keep this direction or adapt it to your products, brand colours and budget.

Component specification & sample checksSix parts to review when you are ready
Proposed construction — final dimensions and materials follow sample review
ComponentStarting directionConfirm before production
Rigid shellWrapped greyboard base with an attached book-style lid and rectangular front flap.Board thickness, usable internal size, hinge movement, corner wrapping and lid clearance with all three products loaded.
Wrap & liningFine-textured matte blue-grey paper outside; warm ivory paper inside.Paper grade, colour reference, print response, rubbing and fold appearance on the selected stock.
BrandingA single navy logo on the outer lid. Interior branding can be reviewed separately.Original vector artwork, print colour, size and position. Any foil or embossing is an optional change to quote.
Paperboard insertDie-cut openings, folded support walls and finger access for the bottle, jar and tube.Filled weights, support heights, board stiffness, edge contact, loading method and resistance to movement.
Magnetic closureConcealed magnets in the front flap and corresponding closure area.Position, alignment and opening effort. The closed lid must remain clear of the pump, jar lid and tube.
Transit packA separate outer shipping carton and cushioning appropriate to the packed set.Orientation, closure security, packed weight and checks for the actual delivery route.

Cost priorities: review box size and insert complexity before adding decoration. Quote paper, printing, tooling, packing and quantity against the same approved scope.

What can change for your brand?Palette, set contents and layout

Colour & artwork

Change the wrap, lining and logo treatment. Review a physical colour sample on the chosen paper.

Product combination

Adapt the set to your bottle, jar or tube sizes. Recheck the outer box whenever the tallest or widest product changes.

Insert construction

Adjust openings, supports and access notches. Heavier containers may need extra reinforcement or a different insert route.

Could this work for another product set?Skincare, hair care, spa and fragrance

Skincare & hair care

Combine bottles, jars and tubes. Adapt support heights for taller dispensers and heavier containers.

Spa & hospitality

Arrange lotions, soaps and accessories together. Review contact surfaces and the packing sequence.

Fragrance sets

Pair perfume with companion products. Allow for glass weight, cap clearance and separation.

Adapt this gift box to my products ↗︎

Explore cosmetic packaging ↗︎Need separate cartons? See the skincare series ↗︎

Samples
and ordering.

Sales will confirm sample options, costs and production / delivery timing for your project.

What should the physical sample confirm?Fit, access and the complete pack
  1. 01 / LOAD THE ACTUAL PRODUCTS

    Confirm size and support.

    Use the intended filled containers, with the pump and closures in their packing positions. Confirm support, separation and usable box height.

  2. 02 / OPEN, REMOVE & REPACK

    Check the whole interaction.

    Close the lid without pressing any product. Open the flap and lid, then lift and replace each container without pinching or rubbing.

  3. 03 / APPROVE THE PACKED SET

    Record the final scope.

    Approve materials, artwork and packing instructions together. Agree transit packing and handling checks, and retain the signed-off sample version.

What is the minimum order, and what is included?

The minimum order is 500 pieces for all box types. This project covers the paper box and agreed insert; containers, formulations and filling are outside the default scope. Share quantities by design and the delivery destination for a scoped quotation.

Can different gift sets share the same outer box?

Possibly, if each set fits the same usable footprint and height. Separate insert versions can accommodate different containers. Review every product combination and identify each insert version for packing; a shared outer size does not establish a shared fit.

Can the set travel with the bottle and tube lying down?

Confirm the permitted orientation and closure condition with your product supplier. Review the filled containers, any leakage precautions and the outer transit pack together. The paper insert supports the presentation; it does not establish leak resistance or transport performance.

Review supplier informationProcesses, samples and quality records

Physical test results are not shown here. Ask sales about relevant wrapping, printing and insert processes, plus available sample or quality records.

Factory & quality information ↗︎Request supplier information ↗︎
APPLY THE IDEA TO YOUR PRODUCT

Choose your next packaging decision.

Plan your
body care gift box.

Send a group photo or a short request. Sizes, quantities and artwork can follow.

I have specifications — request a quote ↗︎

Minimum order: 500 pieces.

Discuss my gift set

Case reference included. No options required.

What happens next?

Sales reviews your set and helps define the box, insert and next sample step.